Canon Pixma Pro 10 Install

WiFi Configuration and Driver Installation Process

First of all, place your Canon Pixma Pro-10 printer on a flat and safe place. make sure that it's within the signal range of your network access point i.e. your router.
Now, carefully unbox your printer. Then remove all the packaging material from the within and out of doors of the printer.
Next, you ought to plug the facility cord into the printer and therefore the other end into a wall outlet.
Then, press the “ON” button located on the highest to power it up. confirm that its “Power Lamp” is lit and stable.
Thereafter, unpack the “Printhead” and punctiliously install it in its designated location by adjusting the Paper Tray.
After that, unpack the “Ink Tank” and properly insert it.
As a result, it'll lit the “Printhead” and “Ink” Lamps.
Subsequently, adjust its “Paper Tray” and punctiliously load it with plain A4 size sheets.
After this, just in case if the printer begins the initialization process. Then, await the method to finish .
After completing the physical setup of your printer, proceed for the network configuration. In other words, you'll need to establish a WiFi reference to a network access point or a wireless router.
Now, check out the “Operational Panel” of Canon Pixma Pro-10 printer. Here, you'll find a “WiFi” button with a “WiFi” icon. Hence, press and hold an equivalent . you ought to keep it pressed till the “Alarm Lamp” flashes once.
Then, await the blue “WiFi Lamp” to flash.
After that, you ought to immediately approach your access point i.e. your router. Here, you ought to locate the router’s “WPS” push-button. Then, press it. Another thing to stay in mind is that you simply must press this push-button within 2 minutes of the last step. Hence, it's recommended that you simply should remember of the situation of this “WPS” push-button on your router beforehand. Else you'll need to repeat the whole process again.
Consequently, the blue “WiFi Lamp” on the printer start flashing. this means that the printer is checking out the network. Thereafter, both the “Power and Wi-Fi Lamp” will start flashing. This happens when the printer is establishing a reference to the access point.
Thereafter, both the “Power and Wi-Fi Lamp” will stop flashing and remains lit. It confirms that a successful connection has been established between the printer and router.
Subsequently, you ought to “Test Print” the printer’s “Network Settings” so as to verify that the printer has been successfully configured. For this, make sure that its “Paper Tray” is correctly loaded with plain A4 sized sheets. Then, press and hold the “Resume/ Cancel” button until the alarm lamp flashes 15 times. Subsequently, release it. As a result, it'll print the “Network Settings Page”. Here, you want to confirm certain details. The “Connection” status should be “Active”. The SSID – Service Set Identifier (the name of your wireless network) should indicate the right name of your wireless network.
With this, your Canon Pixma Pro-10 is successfully configured with the web network through the WPS push-button method.
Now, you ought to install the corresponding software/ drivers to your computer in order that it can command the printer. For this, you'll either download the drivers from the Canon printer’s setup website. Else, you'll simply use the Installation CD within the following manner.
Hence, properly insert the installation CD within the computer’s CD drive . As a result, it'll automatically open the Canon Pixma Pro-10 Setup wizard. However, just in case if the “Setup CD-ROM” doesn't autorun. Then, eject the CD and reinsert it into the computer’s CD drive . Thereafter, click on “My Computer” from the “Start” menu of your Windows device. Next, you ought to select CD-ROM and double-click the “Canon Pixma Pro-10 Setup File”. On the opposite hand, Mac users should double-click the “Canon Inkjet” icon from the “Desktop”. Then, click on the “Setup File” from the “Selection Window”.
Now, you want to install the downloaded drivers to your computer. Since the installation process will depend on your computer’s OS. Therefore, follow the relevant procedure as per your OS.

Installation For Windows

The very first window that you will get is the “User Account Control” window seeking your permission for the installation. Hence, click “Yes” to permit.
Consequently, it will open the “Canon Pixma Pro-10 Installation Wizard”. Here, you should click on “Next”.
The next window will prompt you to “Select Your Place Of Residence”. As such, make an appropriate choice and click “Next”.
Thereafter, you will get the “License Agreement” window. Hence, read the details carefully. Then, click on “Yes” to consent for the same.
Subsequently, it will take you to the Extended Survey Program. Here, you will get two options. You may either Agree or Disagree with it. As such, select appropriately. Here you may note that in case if you Agree to it. Then, Canon will have access to certain information recorded in your printer. In other words, your computer will collect the information and send it to Canon through the internet. Canon uses this information for the development and marketing of its products while maintaining the confidentiality of your data.
After this, it will take you to the Firewall Settings window. Hence, ensure that “Deactivate the Block” is selected. Thereafter, click “Next”.
The following window will prompt to confirm your “Connection Method”. Hence, select “Use the printer with wireless LAN connection”. Then, click “Next” to proceed with the Canon Pixma Pro-10 Setup process.
Now, it will prompt you to turn on the printer. Hence, turn on the printer if it is off. Here, you must ensure that the printer’s “Power Lamp” is properly lit and stable.
Thereafter, click “OK”.
Consequently, it will search for Canon Pixma Pro-10 printer on the network. Once the printer is detected. Then, it will proceed with the installation process. As such, you should follow the on-screen instructions to complete the process.
However, in case if it fails to detect the printer. Then, the next window will notify the same. Hence, click “Next” and follow another method to proceed further. Now, in case if the printer is properly connected to the network. Still, the computer can’t detect it. Then, check whether the computer is connected to the same network as the printer or not. In case if the computer is connected to a different network. Then, disconnect it and connect it back to the network which is shared by the printer. Additionally, you should temporarily disable any firewall/ anti-virus on your computer. Then, click on “Redetect”.
On the contrary, if you had clicked “Next” in the last step due to connection issues. Then, the following window will prompt you to connect the printer to the computer through a USB cable. Hence, hook up the printer to your computer through a USB cable. Here, you can click on the “Instructions” tab for a detailed guide.
Once the system detects the printer, follow on-screen instructions to complete the installation process.

Installation For Mac

The very first window will prompt you to permit for the installation process. Hence, click “Yes/ Continue” to proceed.
This will open the “Installation Wizard”. Now, click “Continue” on this initial window.
Now, you will get the “Software License Agreement” window. Hence, review the document carefully. You can even read it in your preferred language. For this, you should click on the “Language” drop-down box. Then, select the language of your choice. After reading the document, click on “Continue” to proceed further. Along with that, you can save it for future reference. Hence, click on the “Save” button before proceeding further.
Consequently, you will get a pop-up box seeking your consent for the “Software License Agreement”. Hence, click on “Agree”.
Finally, you will get the “Installation” window. Here, it will display the disk space required for saving the Drivers. Hence, ensure that your Mac has sufficient free disk space. Then, click on “Install”.
Thereafter, it will prompt you to provide your Mac login credentials. Hence, enter your “mac Administrator User ID and Password” correctly.
Subsequently, click on “Install Software” to proceed with Canon Pixma Pro-10 Setup.
Now, wait for the installation to complete properly. Then, click on “Exit” to close the Installer.
At last, restart your computer to conclude Canon Pixma Pro-10 setup.

pro-10-300x265
ezgif.com-crop
issue
Call Now
Scroll to Top